Whether you're starting an apprenticeship, renovating your first home, or just done waiting for someone else to hang the shelves: here's a starter kit that fits your hands, plain-English reasons for every pick, and a first project you can finish this weekend.
Specs sourced from manufacturers · No hard-coded prices — just $ to $$$ tiers · Updated 2026-10-24
Fit matters more than muscle
Weight with the battery on, tool length and a good clutch decide how much control you have. We put those first.
Buy into one battery family
Batteries only fit one brand's tools. Choose a family once and every future tool gets cheaper to add.
Safety gear that actually fits
Glasses that flex, earmuffs that adjust, gloves cut for women's hands. If it fits, you'll wear it.
Starter kit
Four things to own before your first project
A drill, an impact driver, a circular saw and your safety gear. Pick a kit below — or compare other options on our drills, impact drivers and circular saws pages, or let the quiz choose for you.
The do-it-all kit
DeWalt 20V MAX — one battery family for all three tools
All three tools share DeWalt's 20V MAX batteries, which Lowe's and Amazon both carry. Buy the saw as a kit (DCS565P1 comes with a 5Ah battery, charger and bag) and the drill and impact driver as tool-only — one battery runs everything. Add a second battery when you're ready. source ↗
Drives long screws without twisting your wrist. Under 4" long, so it fits inside cabinets and between joists — and its low speed setting is gentle on small screws.
The Original Pink Box 20V — matching, brushless, honest about limits
If you want your tools to look like yours, this is the most capable all-pink system we found. The drill and impact driver are genuine brushless tools. The saw is fine for plywood and 2x4s, but it's slower and shallower than the DeWalt — so we'd pair a pink drill and impact with whichever saw you'll feel safest using. source ↗
Left-side blade gives right-handed users a clear view of the line. Lower speed (3,650 RPM) and 2" depth — great for shelving and boxes, not our pick for decks.
Every saw and drill manual calls for eye protection. These flex to fit different head sizes — handy if 'one size fits all' glasses usually slide off you — and the flat temples sit comfortably under earmuffs.
StandardMeets ANSI Z87.1, CSA Z94.3 and AS/NZS 1337
LensesAnti-fog, scratch-resistant; block 99.9% of UV
FitFlexible temples conform to different head sizes; soft adjustable nose pads
Works withLow-profile flat temples designed to work with hearing protection
Impact drivers and saws are loud — DeWalt declares 88 dB(A) for its compact impact driver and 91 dB(A) for its compact saw. Earmuffs go on and off in a second, and the headband adjusts to smaller heads.
Noise Reduction RatingNRR 30 dB (3M advises planning on about half the NRR in real use)
FitFlexible headband adjusts to multiple head sizes; pivoting cushioned cups
Gloves cut for women's hands mean no floppy fingertips catching on things. Wear them for carrying lumber and handling rough boards — choose a snug size so nothing loose ends up near a spinning blade or bit.
SizesWomen's Small, Medium, Large (Mechanix recommends sizing down if between sizes)
Sawing and sanding make fine dust you don't want to breathe. The exhalation valve keeps it cooler, and the adjustable nose clip lets you shape a snug seal over your nose.
RatingNIOSH-approved N95 (approval TC-84A-1299)
Use forSanding, sawing, woodworking, sweeping, drywall cutting
Do NOT use forGases, vapors, oil aerosols, asbestos or lead
Safety glasses on for every cut and every drilled hole; earmuffs for the saw and impact driver.
Support the board on both sides of the cut and clamp it — both hands stay on the saw.
Let the blade reach full speed before it touches the wood, and wait for it to stop before lifting.
Take the battery out before changing a blade or bit, or adjusting the saw.
Wear the N95 when sanding. Saw safety details, sourced from the makers' manuals: Your first cut.
Step by step
Mark your cuts
Measure 16" from one end of the board, hook a speed square on the edge and draw a square line. Mark an X on the waste side. Mark one piece at a time — measure each new piece from the fresh cut, not from the far end.
Cut the six pieces
Glasses and earmuffs on. Clamp the board with the waste end hanging past your support, set the blade about half a tooth deeper than the board, let the saw reach full speed, then push smoothly through. Let the blade stop before you lift. New to this? Read Your first cut first and practice one cut on scrap.
Sand the edges
Mask on. Sand every cut edge with 120 grit until it feels smooth, then do a quick pass with 220. Soften the sharp corners slightly.
Dry-fit the box
Stand the two ends (B) between the two long sides (A) so the long sides cover the ends' cut edges. Check that the box sits flat and the corners look square.
Glue, pilot, screw
Run a thin bead of glue on an end's cut edge, clamp it between the sides, then drill two pilot holes with the countersink bit through each side into the end. Drive #8 × 1-5/8" screws with your impact driver on its lowest speed (or your drill with the clutch set low) until the heads sit flush. Repeat for all four corners.
Add the bottom
Flip the box over. Lay the two bottom boards (C) side by side, glue the edges they sit on, then pilot and drive two or three screws into each long side and one into each end.
Finish it your way
Wipe off any glue squeeze-out with a damp cloth, give it a final sand, and leave it natural, paint it, or stain it. Use it as a planter liner tray, a toy box, a tool tote, or entryway storage.
The best part
You built that.
Measured, cut, drilled and drove every screw yourself. Every bigger project — shelves, planters, a workbench — is just more of what you did today. Share it, use it, and go build the next thing.
We may earn a commission from Lowe's, Amazon and other retailers when you buy through links on this page, at no extra cost to you. It never changes what we recommend. Affiliate disclosure.